The key point of intelligent cooling is the advanced international brand's configuration and performance. It adopts high configuration, high quality, automatic control of water content, asphalt content, operation speed and mixing depth in the process of regeneration, achieving GPS positioning and remote fault diagnosis, and achieving advanced world level. It is a new generation of cement pavement recycling machinery with reliable reliability.

以冷再生租賃機為例，它配備了如下的智能控制系統：

Take the cold regeneration rental machine as an example, it is equipped with the following advanced intelligent control system:

1.動力采用康明斯發動機，功率為500HP。

1. Cummins engine with 500hp power is adopted.

2.作業轉子驅動采用機械（皮帶）傳動，動力傳動比液壓傳動效率提高25%，皮帶傳動使沖擊載荷免于傳到發動機上，根據不同的負載情況通過置換皮帶輪可得到不同的轉速。

2. Mechanical (belt) drive is adopted for operation rotor drive. The efficiency of power transmission is 25% higher than that of hydraulic transmission. Belt drive prevents impact load from being transmitted to the engine. Different speeds can be obtained by replacing the pulley according to different load conditions.

3.轉向方式有前輪轉向、蟹型轉向、后輪轉向、全輪轉向，因此具有良好的機動性能。

3. The steering modes include front wheel steering, crab steering, rear wheel steering and all wheel steering, so it has good maneuverability.

4.本機具有功率自動分配功能，當銑拌阻力增加發動機轉速下降時，微控器能夠調節行走系統的功率，補償銑拌系統的功率，保證該機在大效率和大生產率狀態下工作。

4. The machine has the function of automatic power distribution. When the milling resistance increases and the engine speed decreases, the micro controller can adjust the power of the walking system and compensate the power of the milling system, so as to ensure that the machine can work under the condition of high efficiency and high production rate.

5.液體噴灑計量系統，微控器能夠根據行走速度銑拌深度及銑拌寬度自動調節噴灑量的大小，實現噴灑量的精 確計量控制，滿足舊瀝青路面的再生要求

5. Liquid spraying metering system, micro controller can automatically adjust the spraying amount according to the walking speed, milling depth and milling width, realize the accurate metering control of spraying amount, and meet the recycling requirements of old asphalt pavement

6.裝備MOBA銑刨機找平系統，MOBA銑刨機找平系統專為控制銑刨機工作時的銑刨深度設計，通過傳感器對銑刨鼓相對于銑刨機機身位置的距離變化進行檢測，將變化量轉化為電信號傳輸給控制器，再由控制器自動對銑刨鼓進行調整，從而實現對銑刨深度的自動控制。

6. Equipped with MoBa milling machine leveling system, MoBa milling machine leveling system is designed to control the milling depth when the milling machine is working. The sensor detects the distance change of the milling drum relative to the milling machine body position, converts the change into electrical signal and transmits it to the controller, and then the controller automatically adjusts the milling drum, so as to realize the automatic control of the milling depth.

7.本機具有GPS遠程故障診斷系統，使用GPS遠程監控系統，可實現設備的全球定位、設備工作信息監控、故障診斷、遠程維護和報警，以及鎖車、防盜等功能。通過嵌入式計算機技術和移動通信技術搭建的服務管理平臺，能通過網絡終端實時遠程監控，實施遠程管理。

7. This machine has a GPS remote fault diagnosis system. Using the GPS remote monitoring system, it can realize the global positioning of the equipment, monitoring of equipment working information, fault diagnosis, remote maintenance and alarm, as well as locking and anti-theft functions. The service management platform built by embedded computer technology and mobile communication technology can realize real-time remote monitoring and remote management through network terminal.

（1）能夠遠程觀測到設備所處的地理位置以及現場施工軌跡及觀測到其施工區范圍。

(1) It can remotely observe the geographical location of the equipment, the construction track and the construction area.

（2）能夠進行車輛發動機各項參數、工作狀態、油壓的運行情況和運行異常報警預告的實時信息狀態查。

(2) It can check the real-time information status of vehicle engine parameters, working status, oil pressure operation and abnormal operation alarm.